Feeder Timer HA18
zoom_out_map
chevron_left chevron_right
New

Feeder Timer HA18

€20.66
 

Secure Payment

 

Shipping Worldwide

 

24/7 Customer Support

Description

The Feeder timer HA18 is a display timer clock for any HUNTERA feeder that can be programmed to feed 1 to 6 times per 24 hours. It can program the feeder motor to run for between 1 and 60 seconds per feed.

Works with 6V and 12V motors.

 

HA-18 TIMER OPERATING INSTRUCTIONS 

SET FEEDING TIME 

1.CONNECT STORAGE BATTERY LEADS. 

1.1 WHEN POWER IS ON, IF THE TWO DOTS ON DISPLAY ARE NOT FLASHING, PLEASE REMOVE POWER LINE FROM BATTERY AGAIN, AFTER ONE MINUTE TO CONNECT AGAIN, THUS TO RESET IT ENOUGH.

1.2 THE TIMER CAN WORK WHEN ONLY POWERED BY STORAGE BATTERY. WHEN POWER IS REMOVED, YOUR SETTING  VALUE WILL BE CLEAR. PLEASE SET AGAIN WHEN POWER IS ON AGAIN.  

1.3 IF WISH TO SAVE SETTING VALUE DURING POWER IS OFF, PLEASE MOUNT THE ACCESSORY CELL(LITHIUM  CELL CR2032) TO AS RESERVE POWER FOR MEMORY. 

1.4 IF NOT WORK,NOT DISPLAY OR SETTING NOT BE SAVED, PLEASE REPLACE THE FRESH CELL(CR2032) INSIDE  THE TIMER 

2.SET CURRENT TIME BY PRESSING THE DESIGNATED “HR” AND “MIN” BUTTONS. 

3.BRIEFLY PRESS AND RELEASE THE “PROG” BUTTON TO DISPLAY “SPIN” (1-6). PRESS “HR” AND “MIN” BUTTONS TO SET DESIRED “SPIN” TIME. 

4.PRESS AND RELEASE “PROG” BUTTON AGAIN TO DISPLAY THE ASSOCIATED “SPINTIME” (1-6). USE “HR” AND “MIN” BUTTONS TO SET “SPIN TIME” (0-60 SECONDS). 

5.REPEAT STEPS 3 AND 4 FOR SETTING ADDITIONAL SPIN CYCLES. IMPORTANT NOTE: FOR SIMPLICITY OF “PROG” NAVIGATION, THE DEFAULT SETTING FOR “SPINS” IS SET TO “OFF”. THIS RESULTS IN “SPIN” (4-6)  BEING HIDDEN. ENABLING “SPIN3” WILL UNHIDE “SPIN4” ONLY. EACH SUBSEQUENT “SPIN” MUST BE ENABLED  TO MAKE ALL 6 “SPIN” CYCLES AVAILABLE. 

 

MOTOR SPEED CONTROL 

1.PRESS AND HOLD THE “PROG” BUTTON UNTIL “MOTOR SPEED” IS DISPLAYED. USE “HR” AND “MIN” BUTTONS TO SELECT DESIRED MOTOR SPEED. AVAILABLE SPEED SELECTIONS ARE ‘LOW”, “MID” & “HI”. 

 

SYSTEM TEST 

1.PRESS “TEST” BUTTON. (WARING: MOTOR DISCHARGES FEED AT HIGH VELOCITY!) 

 

CLEAR MEMORY 

1.PRESS AND HOLD “PROG”,“HR” AND “MIN” BUTTONS FOR 5 SECONDS TO RESET ALL FEED TIMES. 

 

RUN AND SOLAR CHARGER LED LIGHT  

1.THE RUN LED LIGHT WILL BE LIGHTED AND FLASHING QUICKLY MORE AND MORE 1 MINUTE BEFORE RUN. 

AFTER SOLAR PANEL IS INSTALLED AND CHARGING, THE SOLAR LED LIGHT WILL BE FLASHING  PLEASE NOTE: THE BATTERY MUST BE LEAD-ACID STORAGE BATTERY TYPE. 

 

 

WIRE CONNECTION FOR TIMER

No. 

2

SOLAR PANEL PLUG

ITEM 

BATTERY 

(+)

BATTERY 

(-)

MOTOR 

(+)

MOTOR 

(-)

SOLAR 

(+)

SOLAR 

(-)

COLOR 

RED 

BLACK 

ORANGE 

BLUE 

WHITE 

BROWN


 

Data sheet

203030093
7 Items